How to Remove and Also Replace a Bathtub
How to Remove and Also Replace a Bathtub
Blog Article
This article down below on the subject of How to Install a Bathtub Yourself is indeed attention-grabbing. Give it a go and make your own final thoughts.
Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the job can move immediately; if you need to open up a wall surface to eliminate the old tub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will need a helper to move out the old tub and also embeded in the brand-new one. Make certain you have qualified yourself for the job and fit trying it. Instead of employing a specialist to take over a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you might require a professional plumber to make tube links.
This post will aid you set up a new bath tub in your shower room if you have currently purchased a brand-new bathtub and do not need to transform the plan of your previous water supply pipelines.
Your tools and also product checklist need to make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washers are in place between the faucet as well as the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The former kind must be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bath tub
Utilizing the two wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four little points.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the tub up until the spirit level reviews degree.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the water supply and also check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as also examine the overflow outlet and the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the tub has been made use of a minimum of once as this will certainly settle it right into its final placement.
Getting ready for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the tap includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall surface between the bath and also the tiling, leading to problems with wetness and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and also installations. They are marketed in tubes and cartridges, and are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the activity experienced when the bathtub remains in use. The sealant can break relatively very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily offered on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very eager about How to Install a Bathtub and I really hope you enjoyed reading the entry. If you enjoyed reading our blog posting if you please remember to share it. Thanks so much for your time invested reading it.
Click For More Information
Report this page